Guide: Installing uniGMap 1.4.8 Full Source in Delphi 10.2 Tokyo uniGMap is a popular component for integrating Google Maps into Delphi applications. Version 1.4.8 is a stable release frequently used with classic IDE versions like XE2 and Delphi 10.2 Tokyo . This guide walks you through a manual installation from the full source code. 1. Prepare Source Files Extract Files : Unzip your UniGMap 1.4.8 full source into a permanent directory on your machine (e.g., C:\Components\UniGMap ). Locate Packages : Inside the source folder, look for the package file. For Delphi 10.2 Tokyo , you typically want a package named for the "D25" version (the internal version number for Tokyo) or a general UniGMap.dpk . 2. Configure Library Paths Before the IDE can compile the source, it must know where the units are located: Open Delphi 10.2 Tokyo . Navigate to Tools > Options . Go to Language > Delphi > Library . Select your target platform (e.g., Windows 32-bit ) and click the ellipsis next to Library path . Add the directory where you extracted the UniGMap source code. 3. Build and Install the Package Open Package : Go to File > Open and select the UniGMap package file (e.g., UniGMap_D25.dpk ). Build : In the Project Manager , right-click the package and select Build . This generates the necessary .dcu and .bpl files. Install : Right-click the package again and select Install . If successful, you will receive a notification that the components have been registered. Verify : You should now see the UniGMap components in your Component Palette . 4. Troubleshooting Common Issues "Unit Not Found" : This usually means the Library Path was not set correctly in Step 2. Double-check that it points to the folder containing the .pas files. Ambiguous References : Ensure you don't have multiple versions of UniGMap in your search paths. Compiler Errors : Ensure you are using the correct package version for Tokyo (D25). Avoid using the "Clean" command on the project, as it may remove required pre-compiled files. For further assistance, many developers reference community discussions on sites like Delphi-PRAXiS or the uniGUI forums for specific component integration tips. unigmap 148 xe2delphi 102 tokyo full source install
If you are looking to perform a full source installation of a component suite (like uniGUI) for Delphi 10.2 Tokyo, follow these general steps adapted from standard manual installation practices : 1. Preparation Close the IDE : Ensure Delphi 10.2 Tokyo is completely closed before starting the installation. Administrator Rights : Always run the installer or your IDE with the same user privileges used during the initial Delphi installation to avoid registry or folder permission issues. 2. Full Source Compilation If you have the "Full Source" version, you must compile the packages for your specific IDE version (Delphi 10.2 Tokyo): Locate the Package Group : Look in the source folder for a .groupproj or multiple .dpk files. For Delphi 10.2, these are often labeled with D25 , 102 , or Tokyo (e.g., uniGUI_D10_2_Tokyo.groupproj ). Open and Build : Open the project group in the Delphi IDE. Right-click on the project group in the Project Manager and select Build All . Note : Avoid using the "Clean" command, as it can delete essential pre-compiled files needed for some installations. Install Design-Time Packages : Locate the packages ending in dcl... (design-time packages). Right-click these specific packages and select Install . A dialog should appear confirming the components have been registered. 3. Configuring Library Paths The IDE needs to know where to find the source and compiled files ( .dcu ) to compile your projects: Go to Tools > Options . Navigate to Language > Delphi > Library . Select the target platform (e.g., Windows 32-bit ). In the Library Path , add the full paths to the following folders: The \Source folder. The \Lib or \DCU folder where the .dcu files were generated during the build step. Repeat this for other platforms (like Windows 64-bit ) if you plan to target them. 4. Verification Create a new VCL Forms Application . Check the Component Palette for the new tab (e.g., "uniGUI" or "Devart"). Drop a component onto the form and try to Compile (Ctrl+F9) to ensure the library paths are correctly configured. For official documentation on specific suites, you can refer to the Devart UniDAC Installation Guide or the uniGUI Commercial Installation Guide . Installing Component Packages Manually - Embarcadero Blogs
Installing UniGMap 1.48 with XE2 Delphi 10.2 Tokyo — Full Source Guide This article shows a step-by-step workflow to build and install UniGMap 1.48 (full source) into Embarcadero Delphi XE2 configured to target a modern Tokyo-style library layout (assumes Delphi XE2 IDE on Windows). It covers source preparation, library paths, package compilation order, design-time vs runtime packages, and common build fixes. Follow exactly and adapt paths and package names to your local source tree. Prerequisites
Windows 7/8/10, 64-bit recommended. Delphi XE2 installed and updated with the latest XE2 patches. UniGMap 1.48 full source archive (unzipped to C:\Dev\UniGMap-1.48 for examples). Basic familiarity with Delphi packages (.dpk), units (.pas), and IDE package compilation. Administrative permissions for writing to Program Files (if installing into IDE folders). unigmap 148 xe2delphi 102 tokyo full source install
Directory layout (assumed)
C:\Dev\UniGMap-1.48\ — root of the UniGMap source.
source\ — unit source files (.pas, .dpr, .dproj) packages\ — Delphi package projects (.dpk) grouped by runtime/design-time examples\ — demo projects libs\ — any third-party libraries required by UniGMap Adjust paths below to match your layout. Guide: Installing uniGMap 1
Read the included README / INSTALL
Open UniGMap-1.48\README or INSTALL first. Note any listed third-party dependencies and license requirements. Identify package naming convention (e.g., UGMapRT_ .dpk and UGMapDT_ .dpk, or similar).
Resolve third-party dependencies
Copy any required third-party libraries (Delphi components, DLLs, or static assets) into libs\ and examples\ as instructed. If the code references components you don’t have (e.g., Indy, FastMM replacement, Graphics libraries), install those into XE2 first. For missing DCUs, locate the matching source or get the vendor packages compiled for XE2.
Configure Delphi XE2 Library Paths