Simos 33a Pinout Top [better] Jun 2026

You can find detailed wiring diagrams and full 80-pin maps on technical document platforms like: Simos 3 Motor Management Overview (via Scribd). Simos 1.6L Wiring Diagram (via Scribd).

: Typically identified by a small dot or a molded "1" near one of the corners of the connector housing. Reading Sequence simos 33a pinout top

Based on the query "simos 33a pinout top" (referring to the top side of the ECU board), here is the top-side pinout. You can find detailed wiring diagrams and full

If bench reading fails, some variants require grounding specific pads on the PCB (BSL mode) to enable programming. Always "probe" or verify continuity to the processor pins before applying voltage to unknown pads. Reading Sequence Based on the query "simos 33a

| Pin | Function | Signal Type | Notes | |-----|----------|-------------|-------| | 1 | Ignition coil output (cyl 1) | Output | Low side driver | | 2 | Injector output (cyl 1) | Output | Saturation driver | | 3 | Injector output (cyl 2) | Output | | | 4 | Injector output (cyl 3) | Output | | | 5 | Injector output (cyl 4) | Output | | | 6 | Fuel pump relay control | Output | Grounds relay coil | | 7 | Lambda probe heater (front) | Output | Ground side | | 8 | Throttle valve position sensor (TPS) ground | Sensor Ground | | | 9 | TPS signal (wiper) | Input | 0.5-4.5V | | 10 | TPS 5V supply | Output | +5V reference | | 11 | Intake air temp (IAT) signal | Input | | | 12 | Coolant temp (ECT) signal | Input | | | 13 | MAP sensor signal | Input | Manifold absolute pressure | | 14 | MAP sensor 5V supply | Output | | | 15 | MAP sensor ground | Sensor Ground | | | 16 | Ignition coil output (cyl 2) | Output | | | 17 | Ignition coil output (cyl 3) | Output | | | 18 | Ignition coil output (cyl 4) | Output | | | 19 | +12V main relay output | Power | To sensors/actuators | | 20 | +12V permanent (battery) | Power | Direct from battery | | 21 | +12V from main relay | Power | ECU main supply | | 22 | Ground (power) | Ground | High current | | 23 | Ground (power) | Ground | High current | | 24 | Ground (sensor) | Sensor Ground | | | 25 | CAN High (if equipped) | Comm | Drivetrain CAN | | 26 | CAN Low (if equipped) | Comm | | | 27 | Knock sensor 1 signal | Input | | | 28 | Knock sensor 2 signal | Input | | | 29 | Crank position sensor (CKP) signal | Input | 60-2 wheel | | 30 | CKP sensor ground | Shield/Ground | | | 31 | Cam position sensor (CMP) signal | Input | Hall effect | | 32 | CMP sensor supply | Output | +5V or +12V | | 33 | CMP ground | Ground | | | 34 | Lambda probe signal (front) | Input | 0-1V narrowband | | 35 | Lambda probe ground (front) | Ground | | | 36 | Vehicle speed sensor (VSS) | Input | | | 37 | Brake light switch signal | Input | | | 38 | Clutch switch signal | Input | | | 39 | A/C request signal | Input | | | 40 | A/C compressor enable | Output | | | 41 | EPC warning lamp | Output | | | 42 | Check engine lamp (MIL) | Output | | | 43 | Diagnostic K-line (ISO 9141) | Comm | | | 44 | Idle air control (IAC) - close | Output | Stepper motor coil | | 45 | Idle air control (IAC) - open | Output | Stepper motor coil | | 46 | EVAP purge valve control | Output | | | 47 | Secondary air injection (SAI) relay | Output | | | 48 | Oxygen sensor heater (rear) | Output | If present | | 49 | Idle air control (IAC) - coil B | Output | | | 50 | Idle air control (IAC) - coil A | Output | | | 51 | Not used | - | | | 52 | Not used | - | | | 53 | +12V switched (e.g., from alternator) | Input | Load signal | | 54 | Power ground | Ground | | | 55 | Power ground | Ground | | | 56 | Sensor ground | Ground | | | 57 | Ignition switch input (Terminal 15) | Input | +12V when key ON | | 58 | Start signal (Terminal 50) | Input | +12V during cranking | | 59 | Engine speed output (to tachometer) | Output | Low side driver | | 60 | +12V backup (for adaptive memory) | Power | Permanent |

The connector has 4 rows (A, B, C, D) with 15 pins each.